Omron 2 Wire Proximity Sensor

Omron 2 Wire Proximity Sensor

Table of Contents

Omron 2 Wire Proximity Sensor menggunakan osilasi frekuensi tinggi. Mereka menahan panas, bahan kimia, dan air lebih baik daripada Sensor Persegi Panjang. Mereka tersedia dalam model berpelindung dan tidak berpelindung.

Sensor Kedekatan tersedia dalam model yang menggunakan osilasi frekuensi tinggi untuk mendeteksi objek logam besi dan non-besi dan dalam model kapasitif untuk mendeteksi objek non-logam. Model tersedia dengan ketahanan lingkungan, tahan panas, tahan terhadap bahan kimia, dan tahan terhadap air.

Fitur Omron E2EH-X D DC 2 Kabel

  • Peningkatan ketahanan terhadap deterjen dan karat
  • Berlaku hingga 120C (dengan koneksi DC 3 kabel) (Tahan panas terverifikasi hingga 1.000 jam.)
  • Tahan deterjen dan disinfektan khas yang digunakan dalam industri makanan
  • Tahan air di bawah suhu tinggi, pembersihan tekanan tinggi berdasarkan DIN 40050-9. (Tekanan: 8.000 hingga 10.000 kPa, Suhu air: 80C, Selama 30 detik di semua sudut

Spesifikasi

Size Shielded M12 M18 M30
Shielded
Item            Model E2EH-X3D@ E2EH-X7D@ E2EH-X12D@
Sensing distance 3 mm 7 mm 12 mm
Set distance *1 0 to 2.4 mm 0 to 5.6 mm 0 to 9.6 mm
Differential travel 15% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data (Reference Value) on page 6.)
Standard sensing object Iron, 12 ´ 12 ´ 1 mm Iron 21 ´ 21 ´ 1 mm Iron 36 ´ 36 ´ 1 mm
Response frequency *2 500 Hz 300 Hz 100 Hz
Power supply voltage (operating voltage range) 12 to 24 VDC, ripple (p-p): 10% max.
(10 to 32 VDC, however, 24 VDC max. at temperatures over 100°C)
Leakage current 0.8 mA max.
Control out- put Load current 3 to 100 mA (however, 3 to 50 mA at 100 to 110°C)
Residual voltage *3 Polarity Models: 3 V max.
No polarity Models: E2EH-X@D@-T: (5 V max. *3 (Load current: 100 mA, Cable length 2 m)
Indicators D1 Models: Operation indicator (red), Setting indicator (yellow) D2 Models: Operation indicator (yellow)
Operation mode (with sensing ob- ject approaching) D1 Models: NO       Refer to the timing charts under I/O Circuit Diagrams on page 7 for details. D2 Models: NC
Protection circuits Surge suppressor, Load short-circuit protection
Ambient temperature range Operating: 0 to 100°C (0 to 110°C 1,000 h) *4 Storage:     -25 to 70° (with no icing or condensation)
Ambient humidity range 35% to 95%
Temperature influence ±10% max. of sensing distance at 23°C in the temperature range of 0 to 70°C.
±15% max. of sensing distance at 23°C in the temperature range of 70 to 100°C.
-15% to +20% of sensing distance at 23°C in the temperature range of 100 to 110°C.
Voltage influence ±10% max. of sensing distance at a rated voltage in the 15% rated voltage range.
Insulation resistance 50 MÙ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min between current-carrying parts and case
Vibration resistance Destruction: 10 to 55 Hz 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance Destruction: 1,000 m/s2, 10 times each in X, Y, and Z directions
Degree of protection IEC IP67, DIN 40050-9 IP69K *5
Connection method Pre-wired Models (Standard cable length 2 m), Connector Models
Weight (packed state) Pre-wired Models Approx. 80 g Approx. 145 g Approx. 220 g
Connector Models Approx. 30 g Approx. 55 g Approx. 125 g
Materials Case, clamping nut Stainless steel (SUS316L)
Sensing surface PBT
Cable A heat-resistant PVC cable (Pre-wired model)
Accessories Instruction manual

*1. Gunakan indikator kuning pada Model D1 sebagai panduan.

*2. Frekuensi respons adalah nilai rata-rata.

Kondisi pengukuran adalah sebagai berikut: objek penginderaan standar, jarak dua kali objek penginderaan standar, dan jarak yang ditetapkan setengah jarak penginderaan.

*3. Tegangan sisa dari setiap Model E2EH-X@D@ DC 2-Wire adalah 5 V. Saat menghubungkan ke perangkat, pastikan perangkat dapat menahan tegangan sisa. (Lihat halaman 9.)

*4. Pengoperasian dengan catu daya selama 1.000 jam telah diverifikasi pada suhu 110°C. Jangan tekuk kabel berulang kali pada suhu 100°C atau lebih tinggi.

*5. Spesifikasi Tingkat Perlindungan IP69K

IP69K adalah standar perlindungan terhadap air bersuhu tinggi dan bertekanan tinggi yang ditentukan dalam standar Jerman DIN 40050, Bagian 9. Benda uji disemprot dengan air pada suhu 80°C pada tekanan air 80 hingga 100 BAR menggunakan bentuk nosel yang ditentukan dengan kecepatan 14 sampai 16 liter/menit.

Jarak antara benda uji dan nosel adalah 10 hingga 15 cm, dan air disemprotkan secara horizontal selama 30 detik masing-masing pada 0°, 30°, 60°, dan 90° sambil memutar benda uji pada bidang horizontal.

Download Katalog: E2EH-X D DC 2-Wire Models, Omron Proximity Sensor

Omron Long Distance E2EM-X@X@ DC 2-Wire Models

Omron Long Distance E2EM-X@X@ DC 2-Wire Models
Omron Long Distance E2EM-X@X@ DC 2-Wire Models

Fitur

  • Deteksi jarak jauh hingga 30 mm memungkinkan pemasangan yang aman dengan pengurangan masalah karena benda kerja
  • Tidak ada polaritas untuk pemasangan kabel yang mudah dengan DC 2-kawat
  • Pelindung kabel disediakan sebagai standar

Spesifikasi

Size Shielded M12 M18 M30
Shielded Shielded Unshielded Shielded Unshielded
Item                       Model E2EM-X4X@ E2EM-X8X@ E2EM-X16MX@ E2EM-X15X@ E2EM-X30MX@
Sensing distance 4 mm ±10% 8 mm ±10% 16 mm ±10% 15 mm ±10% 30 mm ±10%
Set distance *1 0 to 3.2 mm 0 to 6.4 mm 0 to 12.8 mm 0 to 12 mm 0 to 24 mm
Differential travel 15% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 4.)
Standard sensing object Iron, 12 ´ 12 ´ 1 mm Iron, 18 ´ 18 ´ 1 mm Iron, 45 ´ 45 ´ 1 mm Iron, 30 ´ 30 ´ 1 mm Iron, 70 ´ 70 ´ 1 mm
Response frequency *2 1 kHz 0.5 kHz 0.4 kHz 0.25 kHz 0.1 kHz
Power supply voltage (operating voltage range) 12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.
Leakage current 0.8 mA max.
Con- trol out- put Load current 3 to 100 mA
Residual volt- age *3 5 V max. (Load current: 100 mA, Cable length: 2 m)
Indicators X1 Models: Operation indicator (red), Setting indicator (green) X2 Models: Operation indicator (red)
Operation mode (with sensing object approaching) X1 Models: NO Refer to the timing charts under I/O Circuit Diagrams on page 5 for details. X2 Models: NC
Protection circuits Surge suppressor, Load short-circuit protection
Ambient temperature range Operating: -25 to 70°C, Storage: -40 to 85°C (with no icing or condensation)
Ambient humidity range Operating/Storage: 35% to 95% (with no condensation)
Temperature influence ±15% max. of sensing distance at 23°C in the temperature range of -25 to 70°C
Voltage influence ±1% max. of sensing distance at a rated voltage in the rated voltage ±15% range
Insulation resistance 50 MÙ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions
Degree of protection IEC 60529 IP67, in-house standards: oil-resistant
Connection method Pre-wired Models (Standard cable length: 2 m)
Weight (packed state) Approx. 60 g Approx. 130 g Approx. 150 g Approx. 180 g Approx. 210 g
Case Nickel-plated brass
Sensing sur- face PBT
Clamping nuts Nickel-plated brass
Materi- als Toothed washer Zinc-plated iron
Accessories Instruction manual

Download Katalog : E2EM, Omron-Long-distance Proximity Sensor

Omron Standard Proximity Sensor E2E-X T1 AC/DC 2-Wire Model

Omron Standard Proximity Sensor E2E-X T1 ACDC 2-Wire Model
Omron Standard Proximity Sensor E2E-X T1 ACDC 2-Wire Model

Fitur dan Benefit

  • Sensor Standar untuk mendeteksi besi
  • Beragam variasi. Ideal untuk berbagai
  • Model dengan frekuensi yang berbeda juga tersedia untuk mencegah saling
  • Ketahanan lingkungan yang unggul dengan kabel standar yang terbuat dari PVC tahan minyak dan permukaan penginderaan yang terbuat dari bahan yang
  • tahan pemotongan
  • Berguna untuk membantu mencegah
  • Pelindung kabel disediakan sebagai fitur standar

Rating dan Spesifikasi

Size Shielded M12 M18 M30
Shielded
Item                             Model E2E-X3T1 E2E-X7T1 E2E-X10T1
Sensing distance 3 mm ±10% 7 mm ±10% 10 mm ±10%
Set distance 0 to 2.4 mm 0 to 5.6 mm 0 to 8 mm
Differential travel 10% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 17.)
Standard sensing object Iron, 12 ´ 12 ´ 1 mm Iron, 18 ´ 18 ´ 1 mm Iron, 30 ´ 30 ´ 1 mm
Response frequency *1 DC 1 kHz 0.5 kHz 0.4 kHz
AC 25 Hz
Power supply voltage (operating voltage range) *2 24 to 240 VDC (20 to 264 VDC)
48 to 240 VAC (40 to 264 VAC)
Leakage current DC: 1 mA max.
AC: 2 mA max.
Load current 5 to 100 mA
Control output Residual voltage DC: 6 V max. (Load current: 100 mA, Cable length: 2 m) AC: 10 V max. (Load current: 5 mA, Cable length: 2 m)
Indicators Operation indicator (red), Setting indicator (green)
Operation mode (with sensing object approaching) NO (Refer to the timing charts under I/O Circuit Diagrams on page 21 for details.)
Protection circuits Load short-circuit protection (20 to 40 VDC only), Surge suppressor
Ambient temperature range Operating: -25 to 70°C, Storage: -40 to 85°C (with no icing or condensation)
Ambient humidity range Operating/Storage: 35% to 95% (with no condensation)
Temperature influence ±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C
Voltage influence ±1% max. of sensing distance at a rated voltage in the rated voltage ±15% range
Insulation resistance 50 MÙ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 4,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions
Degree of protection IEC 60529 IP67, in-house standards: oil-resistant
Connection method Pre-wired Models (Standard cable length: 2 m)
Weight (packed state) Approx. 80 g Approx. 140 g Approx. 190 g
Case Nickel-plated brass
Sensing surface PBT
Clamping nuts Nickel-plated brass
Materials Toothed washer Zinc-plated iron
Accessories Instruction manual

Download Catalog: 

Omron Standard Proximity Sensor E2E-X AC 2-Wire Model

Omron Standard Proximity Sensor E2E-X AC 2-Wire Model
Omron Standard Proximity Sensor E2E-X AC 2-Wire Model

Fitur dan Benefit

  • Sensor Standar untuk mendeteksi besi
  • Beragam variasi. Ideal untuk berbagai
  • Model dengan frekuensi yang berbeda juga tersedia untuk mencegah saling
  • Ketahanan lingkungan yang unggul dengan kabel standar yang terbuat dari PVC tahan minyak dan permukaan penginderaan yang terbuat dari bahan yang
  • tahan pemotongan
  • Berguna untuk membantu mencegah
  • Pelindung kabel disediakan sebagai fitur standar

Rating dan Spesifikasi

Size Shielded M8 M12 M18 M30
Shielded Unshielded Shielded Unshielded Shielded Unshielded Shielded Unshielded
Item                 Model E2E-X1R5Y@ E2E-X2MY@ E2E-X2Y@ E2E-X5MY@ E2E-X5Y@ E2E-X10MY@ E2E-X10Y@ E2E-X18MY@
Sensing distance 1.5 mm ±10% 2 mm ±10% 5 mm ±10% 10 mm ±10% 18 mm ±10%
Set distance 0 to 1.2 mm 0 to 1.6 mm 0 to 4 mm 0 to 8 mm 0 to 14 mm
Differential travel 10% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 18.)
Standard sensing object Iron, Iron, 12 ´ 12 ´ 1 mm Iron, Iron, Iron, 30 ´ 30 ´ 1 mm Iron,
8 ´ 8 ´ 1 mm 15 ´ 15 ´ 1 mm 18 ´ 18 ´ 1 mm 54 ´ 54 ´ 1 mm
Response frequency 25 Hz
Power supply voltage (operating voltage range)*1 24 to 240 VAC (20 to 264 VAC), 50/60 Hz
Leakage current 1.7 mA max.
Load current *2 5 to 100 mA 5 to 200 mA 5 to 300 mA
Control output Residual voltage Refer to Engineering Data on page 19.
Indicators Operation indicator (red)
Operation mode (with sensing object approaching) Y1 Models: NO     Refer to the timing charts under I/O Circuit Diagrams on page 21 for details. Y2 Models: NC
Protection circuits Surge suppressor
Ambient temperature range *1*2 Operating/Storage: -25 to 70°C (with no icing or condensation) Operating/Storage: -40 to 85°C (with no icing or condensation)
Ambient humidity range Operating/storage: 35% to 95% (with no condensation)
Temperature influence ±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C ±15% max. of sensing distance at 23°C in the temperature range of -40 to 85°C,
±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C
Voltage influence ±1% max. of sensing distance at a rated voltage in the rated voltage ±15% range
Insulation resistance 50 MÙ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 4,000 VAC (M8 Models: 2,000 VAC), 50/60 Hz for 1 min between current-carrying parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Destruction: 500 m/s2
Shock resistance 10 times each in X, Y, and Z directions Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions
Degree of protection Pre-wired Models: IEC 60529 IP67, in-house standards: oil-resistant Connector Models: IEC 60529 IP67
Connection method Pre-wired Models (Standard cable length: 2 m) and Connector Models
Weight Approx. 60 g Approx. 70 g Approx. 130 g Approx. 175 g
Approx. 15 g Approx. 25 g Approx. 40 g Approx. 90 g
Materials Case Stainless steel (SUS303) Nickel-plated brass
Sensing surface PBT
Clamp- ing nuts Nickel-plated brass
Toothed washer Zinc-plated iron
Accessories Instruction manual

Download Katalog : 

Omron Standard Proximity Sensor E2E-X DC 2-Wire Model

Omron Standard Proximity Sensor E2E-X DC 2-Wire Model
Omron Standard Proximity Sensor E2E-X DC 2-Wire Model

Fitur dan Benefit

  • Sensor Standar untuk mendeteksi besi
  • Beragam variasi. Ideal untuk berbagai
  • Model dengan frekuensi yang berbeda juga tersedia untuk mencegah saling
  • Ketahanan lingkungan yang unggul dengan kabel standar yang terbuat dari PVC tahan minyak dan permukaan penginderaan yang terbuat dari bahan yang
  • tahan pemotongan
  • Berguna untuk membantu mencegah
  • Pelindung kabel disediakan sebagai fitur standar

Rating dan Spesifikasi

Size Shielded M8 M12 M18 M30
Shielded Unshielded Shielded Unshielded Shielded Unshielded Shielded Unshielded
Item                 Model E2E-X2D@ E2E-X4MD@ E2E-X3D@ E2E-X8MD@ E2E-X7D@ E2E-X14MD@ E2E-X10D@ E2E-X20MD@
Sensing distance 2 mm ±10% 4 mm ±10% 3 mm ±10% 8 mm ±10% 7 mm ±10% 14 mm ±10% 10 mm ±10% 20 mm ±10%
Set distance *1 0 to 1.6 mm 0 to 3.2 mm 0 to 2.4 mm 0 to 6.4 mm 0 to 5.6 mm 0 to 11.2 mm 0 to 8 mm 0 to 16 mm
Differential travel 15% max. of sensing distance 10% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on pages 17 and 18.
Standard sensing object Iron, Iron, Iron, Iron, Iron, Iron, 30 ´ 30 ´ 1 mm Iron,
8 ´ 8 ´ 1 mm 20 ´ 20 ´ 1 mm 12 ´ 12 ´ 1 mm 30 ´ 30 ´ 1 mm 18 ´ 18 ´ 1 mm 54 ´ 54 ´ 1 mm
Response frequency*2 1.5 kHz 1 kHz 0.8 kHz 0.5 kHz 0.4 kHz 0.1 kHz
Power supply voltage (operating voltage range) Standard Models: 12 to 24 VDC, ripple (p-p): 10% max. (10 to 30 VDC) US Models and Connector Models Used as UL-certified Models:
12 to 24 VDC, ripple (p-p): 10% max. (The operating voltage range is also the same.) *3
Leakage current 0.8 mA max.
Control output Load current 3 to 100 mA, Diagnostic output: 50 mA for -D1(5)S Models
Residual voltage *4 3 V max. (Load current: 100 mA, Cable length: 2 m, M1J-T Models only: 5 V max.)
Indicators D1 Models: Operation indicator (red) and setting indicator (green) D2 Models: Operation indicator (red)
Operation mode (with sensing object approaching) D1 Models: NO      Refer to the timing charts under I/O Circuit Diagrams on page 20 for details. D2 Models: NC
Diagnostic output delay 0.3 to 1 s
Protection circuits Surge suppressor, Load short-circuit protection (for control and diagnostic output)
Ambient temperature range Operating: -25 to 70°C, Storage: -40 to 85°C (with no icing or condensation)
Ambient humidity range Operating/storage: 35% to 95% (with no condensation)
Temperature influence ±15% max. of sensing distance at 23°C in the temperature range of -25 to 70°C ±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C
Voltage influence ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance 50 MÙ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1000 VAC, 50/60 Hz for 1 minute between current carry parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Destruction: 500 m/s2
Shock resistance 10 times each in X, Y, and Z directions Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions
Degree of protection Pre-wired Models: IEC 60529 IP67, in-house standards: oil-resistant Connector Models: IEC 60529 IP67
Connection method Pre-wired Models (Standard cable length: 2 m), Connector Models, or Pre-wired Connector Models (Standard cable length: 0.3 m)
Weight (packed state) Pre-wired Models Approx. 60 g Approx. 70 g Approx. 130 g Approx. 175 g
Pre-wired Connector Models Approx. 40 g Approx. 70 g Approx. 110 g
Connector Models Approx. 15 g Approx. 25 g Approx. 40 g Approx. 90 g
Materi- als Case Stainless steel (SUS303) Nickel-plated brass
Sensing sur- face PBT
Clamping nuts Nickel-plated brass
Toothed washer Zinc-plated iron
Accessories Instruction manual

Download Katalog: Standard Proximity Sensor E2E

Sumber : Omron.co.id | inaparts.com

Baca Juga :

Share With Your Friends :

Share on linkedin
LinkedIn
Share on email
Email
Share on facebook
Facebook
Share on twitter
Twitter
Share on whatsapp
WhatsApp
Share on telegram
Telegram

you may also enjoy these articles: