Produk Hengstler Tico Time Counter ini benar-benar multitalenta, memiliki hingga tiga preset dan dapat dihubungkan menggunakan konektor plug-and-play. Produk memungkinkan penghitungan dengan frekuensi sangat tinggi hingga 60 kilohertz dan secara universal cocok untuk digunakan sebagai penghitung denyut nadi, takometer, pengatur waktu, penggeser bergeser atau pencacah batch.
Tampilan 6-warna multi-warna yang besar backlit dan mudah dibaca. Fleksibilitas tingkat pemrograman yang ditawarkan oleh penghitung multifungsi ini memungkinkannya digunakan sebagai penghitung waktu dan, jika diperlukan, dengan banyak fungsi yang dapat diprogram. Fungsionalitas tambahan yang ditawarkan oleh Interface RS232 memfasilitasi pemrograman yang cepat dan mudah pada PC dan memungkinkan perangkat untuk berkomunikasi dengan komputer.
- Operasi yang sangat sederhana
- Empat warna lampu latar yang berbeda
- Layar besar dan mudah dibaca
- Menghitung frekuensi hingga 60 kHz
- Tiga preset
- Prescaler 0,0001 – 99,9999
- Interface RS232 (Tico 774)
- USB Interface (Tico 773)
- Asisten pemprograman (Windows XP 32 bit, Windows Vista 32 bit, Windows 7 32 bit)(Tico 773 & 774)
Baca Juga :Â ACR Artex AISLink CA2 AIS Transponder Display
Spesifikasi Hengstler Tico Time Counter
Umum
| Jenis Produk | Tico 772 | Tico 773 | Tico 774 |
| Fungsi | Time counter | ||
| Teknologi | Electronic | ||
| Digits | 6-digit | ||
| Display | 6-digit | ||
| 2-line | |||
| counting display/presets | |||
| leading zero suppression | |||
| a decimal point (up to 4 places) | |||
| Preset | 3 presets | ||
| Interface | – | USB-interface | RS232-interface |
| Tingg Digit [mm] | 1. Line 9.3 mm (0.4 in) | ||
| 2. Line 7.2 mm (0.3 in) | |||
| Display Variant | reflective LCD | ||
| transflective positive LCD, black digits, backlit | |||
| transmissive negative LCD, white digits, red or green backlit, background black | |||
| View Angle | 12:00 | ||
| Relay | 1 or 2 relays | ||
Hengstler Tico Time Counter Electrical
| Voltage | 12-30 VDC |
| 24-240 VAC | |
| Reset | manual reset |
| electrical reset | |
| automatic reset | |
| Signal Times | 0.01 s to 599.99 s or bistable, programmable, tolerance + 10 ms, active on/off |
Baca Juga : Dinel PDU–401–P Programmable Display
| Current Consumption [mA] | < 200 mA at 12-30 VDC reflective |
| < 250 mA at 12-30 VDC with backlight | |
| <250 mA at 24 VAC | |
| <50 mA at 115, 230 VAC | |
| <80 mA at 100-240 VAC switching power supply | |
| Power Consumption | < 5 W <8 W |
| Cable Cross-Section | 1…1.5 mm² (0.0015…0.0023 in²) with the multicore cable end |
| Input Resistance | approx. 10 kOhm |
| Pulse Length min. | 17 ms (30 Hz), 8 µs (60 kHz) |
| Supply Voltage | 12-30 VDC |
| 24, 115, 230 VAC | |
| 100-240 VAC | |
| Count Frequency [Hz] | max. 60 kHz (TTL 20 kHz): Single-channel counting and directional input |
| max. 60 kHz (TTL 20 kHz): differential or totalizing operation | |
| channel (A+B together) | |
| max. 30 kHz (TTL 20 kHz): phase discriminator 1- or 2-fold evaluation | |
| max. 15 kHz (TTL 15 kHz): phase discriminator 4-fold evaluation | |
| attenuated 30 Hz | |
| For further details, see the graphic and manual. | |
| Overload Protection | ext. backup |
| DC: 0.16 AT (IEC 127), DC: 0.2 AT (UL 198) | |
| 24 VAC: 315 mAT | |
| 115 VAC: 63 mAT | |
| 230 VAC: 32 mAT | |
| 100-240 VAC 630 mAT | |
| Overload Protection Relay Output | ext. backup 230 V |
| 2.5 A mT | |
| Sensor Supply | transformer power supply: 12-24 VDC (load-dependent) |
| max. 50 mA | |
| switch power supply24 VDC -5% | |
| max. 115 mA, max. capacitative load 470 µF | |
| Storage of Values | NVM> 10 years |
| Electrical Connection | pluggable screw terminals / connecting clamps |
| Amplitude Threshold | < 2 V and > 8 V or < 1 V and> 4 V at TTL levels |
| amplitude max. 40 VDC | |
| Active Edge | programmable, positive with PNP input, negative with NPN input |
| Pulse Shape | any square wave (1:1 for max. frequency) |
| Prescaler | 0.0001 – 99.9999 |
| Set Function | set to VW 0 (independent of resets) |
| Display and Preset Range | – 999 999 to + 999 999 |
| Alarm Signal | display blinks |
| when presets 0,1 or 2 are active | |
| Relay (Preset 1 and 2) | Varistor max. 250 VAC / 30 VDC / 5 A |
| Varistor min. 5 VAC / 5 VDC / 10 mA | |
| Delay < 10 ms | |
| Transistor output (Preset 1 + 2) | DC supply: PNP output 12 – 30 VDC, max. 50 mA |
| transformer performance (24, 115, 230 VAC): PNP output 12 – 24 VDC, max. 30 mA | |
| switch power supply 100-240 VAC: PNP output 24 VDC, max. 50 mA | |
| Application Output | DC supply: PNP output 12 – 30 VDC, max. 20 mA |
| transformer performance (24, 115, 230 VAC): PNP output 12 – 24 VDC, max. 20 mA | |
| switch power supply 100-240 VAC: PNP output 24 VDC, max. 20 mA | |
| Attention | Only for transformers (24, 115, m230 VAC: |
| The energy load on the outputs (sensors 12-24 VDC, out1, out2, Appl.-Outp.) may not be more than 65 mA total. |
Counter
| Counter Mode Input A, B | Single-channel add or sub, directional input, |
| differential operation add / sub, totalizing operation add/add, | |
| phase discriminator 1-, 2- or 4-fold evaluation | |
| Preselect Modes | absolute or trailing preset |
| range signal/value limit (Sign. 1 < VW1) | |
| Sign. 2> VW2 | |
| Application Input/Output (Counter) | Output: Prescaler-out |
| preset 0-out | |
| direction-out | |
| input: additional counter input add / sub | |
| reset | |
| set | |
| gate | |
| keylock | |
| hold | |
| teach-in | |
| Mode | batch counter with preset or 2. totalizing counter with preset |
| Count Mode | differential operation add/sub |
| totalizing operation add/add |
Hengstler Tico Time Counter Tachometer
| Measuring Principle (tachometer) | period measurement (1/tau) |
| Display Range | 1/min or 1/sec |
| min. Frequency | 1 Hz or 0.1 Hz |
| Limit Values | 2 alarms with programmable start suppression |
| + 1 additional upper limit on the application input | |
| Tachometer Mode of Operation | Single-channel add or sub, directional input, |
| differential operation add / sub, totalizing operation add / add, | |
| phase discriminator 1-, 2- or 4-fold evaluation | |
| A / B or (A-B) / A % | |
| Application Input/Output (Tachometer) | Output: preset 0-out |
| direction out | |
| input: additional counter input add / sub | |
| gate | |
| keylock | |
| hold | |
| teach-in | |
| Accuracy of the Tachometer Function | Timebase: ± 30 ppm |
| Measuring principle: cycle duration measurement | |
| Measuring time: min. 0.5s / max. 1s or 10s | |
| Measuring resolution: 0,4 µs (<30 ppm) | |
| Display resolution: 4 decimal points | |
| 1 digit = 100 ppm | |
| Overall Tolerance (Tachometer) | = display resolution + tolerance time base = 130 ppm |
Time Counter
| Time Base (Tachometer) | programmable, sec |
| min | |
| h or hh.mm.ss | |
| Measuring Principle (timer) | pulse width or period duration measurement (start-stop) |
| start Inp. A + Stop Inp. B, | |
| Start/Stop button | |
| Function Time Counter | single pulse measurement or cumulative measurement |
| Application Input/Output (Timer) | Output: preset 0-out |
| input: additional Run | |
| Stop | |
| Reset | |
| Set | |
| Keylock | |
| Teach in | |
| Accuracy of the Timer | Timebase. ± 30 ppm |
| Start / Stop time point: 16 µs / 16 ms (unattenuated/attenuated) | |
| resolution: 100 µs = 100 ppm | |
| Overall Tolerance (Timer) | = display resolution + tolerance time base = 130 ppm |
| Resolution | 1, 0.1, 0.01, 0.001, 0.0001 |
Environment and security
| IP Protection Class | IP 65 |
| Operating Temperature [°C] | 0 Â…… + 50 °C (+ 32 … 122 °F) EN 60 068-2-1/2 |
| Storage Temperature [°C] | – 20 … + 65 °C (- 4 … + 149 °F) EN 60 068-2-1/2 |
| Degree of Protection | IP 65 front, EN 60529 |
| IP 20 connections | |
| Cable Length | An additional protective circuit is required when using cables longer than 30 m |
| which are connected to a DC power supply at TTL input levels | |
| General Design | EN 61 010-1 / IEC 61010-1 |
| EMC – Interference immunity | EN 61326-1 Industrial** |
| EMV-Emission | EN 61326-1 Class B* |
| Approvals | UL |
| CSA File-Nr. E 338588 | |
| Vibration Resistance | 10 m/s² (33 ft/s²) (10 . 150 Hz), EN 60 068-2-6 |
| Shock Resistance | 100 m/s2 (328 ft/s2) (18 ms) acc.IEC 068-2-27 |
| Protection Class | II, EN 61010-1 / IEC 61010-1 |
| Contamination Level | V 2 |
| EN 50178 | |
| Climate | 40°C (104 °F)/ 93% RH class 4K4H |
| EN 60 068-2-78 | |
| 25 – 50°C (122 °C) / 93% RH | |
| cyclic | |
| EN 60 068-2-38 | |
| elevations up to 2000 m (6561 ft) | |
| Resistance to Chemicals | front film acc. DIN 42 115-2 |
| RoHS | compliant |
Baca Juga :Â Hengesbach DSA 1010 Digital Display
Mechanical
| Size [mm] | 48x48x118 |
| Mounting Options | Clamping frame |
| Mounting | with clamping frame |
| Reset | manual reset using a keypad |
| external reset static or dynamic | |
| pulse duration min. 5 ms | |
| automatic reset after preset 2 has been reached | |
| no loss of pulse at the maximum counting frequency due to automatic resetting. programmable using application input and power-up reset | |
| Weight [g] | approx. 200 g (3.2 oz) |
| Dimensions [mm] | 48 mm x 48 mm x 118 mm (1.9×1.9×4.6 in), installation depth 110 mm (4.4 in), DIN 43 700 |
| Panel Thickness [mm] | max. 11 mm |
Sumber: hengstler.de/en | Inaparts.com
