Flocorp Tracer 1000 LTT1 Guided Wave Radar Level Transmitter menyediakan pengukuran level berkelanjutan dan deteksi level titik dalam cairan dan padatan, dengan output analog dan switching. Perangkat inovatif ini hampir tidak memiliki batasan pemasangan – dapat dipasang di tangki kecil, nosel tinggi dan sempit, dan mengukur dengan tepat bahkan dengan geometri tangki yang sulit atau dekat dengan struktur yang mengganggu.
Menampilkan teknologi TDR (Time Domain Reflectometry), pengaturan Pabrik dapat dikonfigurasi melalui protokol Komunikasi HART®. Tracer 1000 sangat ideal untuk berbagai jenis aplikasi pemrosesan dan penyimpanan dan memiliki performa luar biasa dalam cairan dengan reflektifitas rendah seperti minyak dan hidrokarbon.
Informasi Flocorp Tracer 1000 LTT1 Guided Wave Radar Level Transmitter
Fitur
- Teknologi TDR Revolusioner
- Pengukuran tingkat berkelanjutan yang tepat dan deteksi tingkat titik yang andal digabungkan dalam satu perangkat
- Pengukuran yang sangat kuat berkat desain 4-kawat dan analisis sinyal yang inovatif serta peredaman sinyal gangguan
- Desain probe sepenuhnya modular – Mudah dipasang
- Menampilkan protokol Komunikasi HART®
- No Dead Band (untuk opsi probe koaksial)
- Harga ekonomis
Baca Juga : Hengesbach K Conductivity Transmitter Condutec
Keunggulan
- Pengukuran yang Andal: Impuls radar frekuensi tinggi
- Pengoperasian yang Mudah: Kalibrasi otomatis ke dielektrik apa pun
- Akurasi Maksimum: Dikalibrasi khusus untuk aplikasi pelanggan
- Keamanan yang Ditingkatkan: Pencegahan luapan dari mode aman gagal yang dapat diprogram
- Sangat Mudah Beradaptasi: Perubahan viskositas, densitas, atau keasaman tidak mempengaruhi akurasi. Permukaan mendidih, debu, busa, uap tidak memengaruhi kinerja perangkat
- Garansi: Tersedia garansi lima tahun
- Ringkasan Spesifikasi
- Rentang: 0″ – 780″
- Pengukuran: Cairan, Bubur, Padatan
- Akurasi: ± 0,12″
- Pemasangan Proses: 3/4″ NPT
- Standar Sertifikasi: NEMA 6 (IP66/ IP68) Tujuan Umum
- Opsional: ATEX, Bukti Ledakan, Zona 1
Baca Juga : Delta Mobrey DPR-2000G Differential Pressure Transmitter
Spesifikasi
| Electrical Specifications | |
| Output Functions | The Tracer 1000 is an active, single ended, non-isolated, 3 or 4 wire analog output transmitter. |
| Analog Output (Active) | Current output 4-20mA: The span between the lower range value [4mA] and the upper range value [20mA] |
| is equal to 0-100% of the continuous level measurement reading as a factory default. Output can be inverted. | |
| Total Load Resistance | < 500Ω: HART resistor approx. 250Ω |
| + load resistance approx. 250Ω if the current output is connected to a device with an inner resistance of approx. 250Ω, then there is no additional external HART resistor necessary. In that case, the HART modem is connected in parallel to the current output wires. | |
| Lower Range Value | 4.0mA (span 0%) |
| Upper Range Span | 20.0mA (span 100%) |
| Response Time | 0.5s (default), 2s 5s (selectable) |
| Temperature Drift | Less than .0078 in/ºF change in ambient |
| temperature | |
| Switch Output | DC Switch, PNP, Active, Max. Load 200 mA Current. |
| Supply Voltage | 12-30VDC (reverse-polarity protected) |
| Current Consumption | < 50mA at 24 VDC (no burden) |
| Start-Up Time | < 6s |
| Cable Terminals | Screwless, cage clamp terminal block for stranded and solid wires AWG 22-14. |
| Measurement Specifications | |
| Accuracy | ± 0.12” or 0.03% of measured distance, whichever is greatest |
| Repeatability | < .08” |
| Resolution | < .04” |
| Probe Type | 316 SS Rod: 1/4” Dia. (Coated Rod; 3/8” Dia.) 316 SS Coaxial: 3/8” Dia. |
| Probe Length [L] | Wire Cable: 1/2” Dia. |
| 316 SS Rod: 2.41” – 120” | |
| 316 SS Coaxial: 0” – 120” | |
| Wire Cable: 2.41” – 480” | |
| (Length must be specified when ordering – The reference point is always the sealing surface of the connection thread – See dimensional drawings) | |
| Top Dead Band | 0” Coaxial Probe |
| 2.41” Rod or Wire Probe | |
| Measuring Range [M] | Up to 780” depending on probe type |
| Switching Point [S] | Freely positionable within the measuring range [M] Hysteresis can be set by defining seperate upper and lower thresholds; if those are set at the same position, the minimum hysteresis of .11” applies |
| Application Specifications | |
| Dielectric Constant [ɛr] | Wire & Cable Probe: Configurable Coaxial Probe: 0 |
| Conductivity | No restrictions |
| Density | No restrictions |
| Standard Application Temp. | F: -40º to 410º C: -40 to 150º |
| Optional Application Temp. | F: -320º to 500º C: -195 to 260º |
| Ambient Temperature | F: -13º to 176º C: -25º to 80º |
| Application Pressure | -14.50 PSI to 580 PSI |
| Velocity of Level Change | |
| Mechanical Specifications | |
| Wetted Materials | 1.4404 / 316L and PEEK, PTFE |
| Enclosure Material | Aluminum alloy EN AC-AISi9Cu3 (DIN EN 1706), Epoxy Spray (~70µm) |
| Enclosure Rating | Standard: NEMA 6 (IP68) |
| Explosion Proof Option: ATEX NEMA 7 | |
| 1/2” NPT (2) or | |
| Cable Glands/Screw Plugs | Cable Glands (2) or |
| Connection Thread | 1/2” NPT (1) & Cable Gland (1) or M20 x 1.5 (2) or |
| M20 X 1.5 (1) & Cable Gland (1) | |
| 3/4” NPT (US) or 3/4” G (Metric) | |
| Weight (Less Probe) | 1.99 lbs. (903.8 g) |
| Certification | FM: Class I Groups A,B,C,D |
| Class II Groups E,F,G; Class III; Type 4X Class I, Div. I, AEx D IIC; IP66 | |
| Class I, Div. I, Ex d II C | |
Baca Juga : Pressure and Level Transmitter PZT 200/201 Hengesbach
Sumber: Flo-corp.com | inaparts.com
