Omron E2EQ Spatter Resistant Proximity Sensor tersedia dalam model yang menggunakan osilasi frekuensi tinggi untuk mendeteksi objek logam besi dan non-besi dan dalam model kapasitif untuk mendeteksi objek non-logam. Model tersedia dengan ketahanan lingkungan, tahan panas, tahan terhadap bahan kimia, dan tahan terhadap air. Sensor Jarak ini menggunakan osilasi frekuensi tinggi. Mereka menahan panas, bahan kimia, dan air lebih baik daripada Sensor Persegi Panjang. Mereka tersedia dalam model berpelindung dan tidak berpelindung. Mereka menahan panas, bahan kimia, dan air lebih baik daripada Sensor Persegi Panjang. Mereka tersedia dalam model berpelindung dan tidak berpelindung. Sensor Kedekatan tersedia dalam model yang menggunakan osilasi frekuensi tinggi untuk mendeteksi objek logam besi dan non-besi dan dalam model kapasitif untuk mendeteksi objek non-logam. Model tersedia dengan ketahanan lingkungan, tahan panas, tahan terhadap bahan kimia, dan tahan terhadap air.
Baca Juga :Â Advanced Sensors EX-400 Side-stream Oil/Particulate in Water Analyzer
Fitur dan Manfaat Omron E2EQ Spatter Resistant Proximity Sensor
- Hujan rintik-rintik unggul
- Model Jarak Penginderaan Jauh ditambahkan untuk jarak penginderaan hingga 15
- Model Konektor Smart click pra-kabel juga
Baca Juga :Â Advanced Sensors SA-100P(2)/1000P(2) In-line Oil In Water Analyzer
Spesifikasi
Long Sensing-distance Models
Model Item | E2EQ-X4X1 E2EQ-X4X1-M1(T)J | E2EQ-X8X1 E2EQ-X8X1-M1(T)J | E2EQ-X15X1 E2EQ-X15X1-M1(T)J | |
Sensing distance | 4 mm ±10% | 8 mm ±10% | 15 mm ±10% | |
Set distance *1 | 0 to 3.2 mm | 0 to 6.4 mm | 0 to 12 mm | |
Differential travel | 15% max. of sensing distance | |||
Standard sensing object | Iron, 12 ´ 12 ´ 1 mm | Iron, 18 ´ 18 ´ 1 mm | Iron, 30 ´ 30 ´ 1 mm | |
Response frequency *2 | 1 kHz | 0.5 kHz | 0.25 kHz | |
Control output | Load current | 3 to 100 mA | ||
Residual voltage *3 | 5 V max. (Load current: 100 mA, Cable length: 2 m) | |||
Operation mode (with sensing object approaching) | Load ON: NO; For details, refer to the timing charts on page 5. | |||
Protection circuits | Load short-circuit protection, Surge suppressor | |||
Ambient temperature range | Operating: -25 to 70°C, Storage: -40 to 85°C, (with no icing or condensation) | |||
Temperature influence | ±15% max. of sensing distance at 23°C in the temperature range of -40 to 85°C ±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C | ±15% max. of sensing distance at 23°C in the temperature range of -25 to 70°C | ||
Voltage influence | ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range | |||
Shock resistance | Destruction: 1,000m/s2 10 times each in X, Y, and Z directions | |||
Connection method | Pre-wired Models (Standard cable length: 2 m), Pre-wired Connector Models | |||
Weight (packed state) | Pre-wired Models | Approx. 65 g | Approx. 140 g | Approx. 190 g |
Pre-wired Connector Models | Approx. 20 g | Approx. 40 g | Approx. 90 g |
Peringkat dan Kinerja Umum
Model  Item | E2EQ-X4X1 E2EQ-X4X1-M1(T)J E2EQ-X3D1 E2EQ-X3D1-M1(T)GJ | E2EQ-X8X1 E2EQ-X8X1-M1(T)J E2EQ-X7D1 E2EQ-X7D1-M1(T)GJ | E2EQ-X15X1 E2EQ-X15X1-M1(T)J E2EQ-X10D1 E2EQ-X10D1-M1(T)GJ | |
Detectable object | Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 4.) | |||
Power supply voltage (operating voltage range) | 12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. | |||
Leakage current | 0.8 mA max. | |||
Indicators | Operation indicator (red), Setting indicator (green) | |||
Ambient humidity range | Operating/Storage: 35% to 95% (with no condensation) | |||
Insulation resistance | 50 MÙ min. (at 500 VDC) between current-carrying parts and case | |||
Dielectric strength | 1,000 VAC for 1 min between current-carrying parts and case | |||
Vibration resistance | Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions | |||
Degree of protection | IEC 60529 IP67, in-house standards: oil-resistant | |||
  Materials | Case | Fluororesin coating (Base material: brass) | ||
Sensing surface | Fluororesin | |||
Clamping nuts | Fluororesin coating (Base material: brass) | |||
Toothed washer | Zinc-plated iron | |||
Accessories | Instruction manual |
Standar Model
Model Item | E2EQ-X3D1 E2EQ-X3D1-M1(T)GJ | E2EQ-X7D1 E2EQ-X7D1-M1(T)GJ | E2EQ-X10D1 E2EQ-X10D1-M1(T)GJ | |
Sensing distance | 3 mm ±10% | 7 mm ±10% | 10 mm ±10% | |
Set distance | 0 to 2.4 mm | 0 to 5.6 mm | 0 to 8 mm | |
Differential travel | 10% max. of sensing distance | |||
Standard sensing object | Iron, 12 ´ 12 ´ 1 mm | Iron, 18 ´ 18 ´ 1 mm | Iron, 30 ´ 30 ´ 1 mm | |
Response frequency * | 1 kHz | 500 Hz | 400 Hz | |
Control output | Load current | 3 to 100 mA | ||
Residual voltage | 3 V max. (Load current: 100 mA, Cable length: 2 m) | |||
Operation mode (with sensing object approaching) | Load ON: NO; For details, refer to the timing charts on page 5. | |||
Protection circuits | Load short-circuit protection, Surge suppressor | |||
Ambient temperature range | Operating/Storage: -25 to 70°C (with no icing or condensation) | |||
Temperature influence | ±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C | |||
Voltage influence | ±2.5% max. of sensing distance at rated voltage in the rated voltage ±15% range | |||
Shock resistance | Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions | |||
Connection method | E2EQ-X@D1: Pre-wired Models (Standard cable length: 2 m) E2EQ-X@D1-M1GJ: Pre-wired Connector Models (Standard cable length: 300mm) | |||
Weight (packed state) | Pre-wired Models | Approx. 120 g | Approx. 160 g | Approx. 220 g |
Pre-wired Connector Models | Approx. 80 g | Approx. 110 g | Approx. 190 g |
Sumber: Omron.co.id | inaparts.com