Articles

ABB LMT200 Magnetostrictive Level Transmitter

ABB LMT200 Magnetostrictive Level Transmitter adalah rentang modular dari pemancar elektronik berbasis mikroprosesor canggih yang dipasang di lapangan, memanfaatkan beberapa teknologi sensor. Pengukuran tingkat cairan dan antarmuka yang akurat dan andal disediakan bahkan di lingkungan industri yang paling sulit dan berbahaya sekalipun.

Informasi Tentang ABB LMT200 Magnetostrictive Level Transmitter

Elektronik perangkat menghasilkan pulsa arus energi rendah pada interval tetap. Pulsa listrik menciptakan medan magnet yang bergerak ke kabel khusus di dalam tabung sensor. Interaksi medan magnet di sekitar kawat dan pelampung magnet menyebabkan gelombang tegangan torsi diinduksi dalam kawat. Torsi ini merambat sepanjang kawat dengan kecepatan yang diketahui, dari posisi pelampung magnet dan menuju kedua ujung kawat.

Elemen penginderaan yang dipatenkan ditempatkan di rakitan pemancar mengubah torsi mekanis yang diterima menjadi pulsa balik listrik. Pemancar Level Magnetostriktif LMT200 mengukur waktu yang berlalu antara pulsa mulai dan kembali (Time of Flight) dan mengubahnya menjadi pengukuran posisi yang sebanding dengan level pelampung.

float direkayasa secara tepat untuk aplikasi pelanggan, memastikan akurasi dan kinerja yang optimal. Magnet dengan jarak yang tepat menciptakan cakupan medan magnet 360°, melindungi pemancar level dan mengukur kinerja, bahkan aplikasi yang paling menantang sekalipun. Beberapa bahan konstruksi tersedia antara lain titanium, Monel®, Hastelloy® C, stainless steel, dan plastik. Lapisan pelindung Tefzel®, Halar®, TEFLON® S juga tersedia. Proses tekanan hingga 344 bar (5000 PSI) hingga vakum penuh.

Fitur

    • Calibrated from the factory
    • High Accuracy: .01% of Full Scale or +/- 1.27mm
    • Never Requires Re-Calibration: Set It & Forget It
    • Easy setup with waveform display
    • Not affected by agitation, foam or emulsion layers
    • No oscilloscope required
    • Designed to Mount Externally to K-TEK KM26 or other
      Magnetic Level Gauge
    • Superior Sensor (Patent #5,473,245)
    • Local Indication with HMI Display
    • Dual Compartment Housing with Separate Field Terminal
      Compartment
    • Loop Powered to 15.24m (50ft) Probe Length
    • Total and/or Interface Level Measurement
    • Temperature Range: -195.5 to 426.6ºC (-320 to 800ºF)
      with options
    • Field Replaceable / Upgradable Electronics Module
    • Built-in RFI / EMI Filter
    • Digital Communications
    • Online Self-verification

Pilihan

  • Two Level Indications
  • Glass Viewing Window
  • 316 Stainless Steel Enclosure
  • Built-in surge protection

Spesifikasi | Electronic Transmitter

  • Repeatability: ± 0.005% of Full Scale or 0.305 mm (0.012 in), whichever is greater
  • Non-linearity: ± 0.01% of Full Scale or 0.864 mm (0.034in), whichever is greater
  • Measuring accuracy: ± 0.01% of Full Scale or 1.27 mm (0.050 in), whichever is greater
  • Supply voltage: 12 to 42 Vdc – 4-20mA HART loop powered
  • Output/Communications: 4-20mA HART7®
  • User Interface: Interactive display, DTM, EDDL with NE107 messaging
  • Power consumption:
    4-20mA: at 36.0 Vdc – 3.6mA 0.13 watts; 21mA 0.76 watts ; at 12.0 Vdc – 3.6mA 0.043 watts; 21mA 0.25 watts
    HART mode (4.0mA): at 36.0 Vdc 0.144 watts ; at 12.0 Vdc 0.048 watts
  • Maximum line resistance:
    4-20mA: at 36.0 Vdc and 21mA, 1142 ohms* ; at 24.0 Vdc and 21mA, 571 ohms ; at 12 Vdc and 21mA, < 72 ohms**
    *Maximum allowable with HART® communication is 700 ohms
    **See the current/resistance chart
    HART mode (4.0mA): < 650 to 700 ohms
  • Polarity protection: 4-20mA, Diode in series with loop, FOUNDATION Fieldbus and Profibus PA, polarity insensitive
  • Update rate: 10 measurements per second
  • Minimum measuring span: 76.2 mm (3.0 in), consult factory if smaller span is required
  • Damping: Field Adjustable, Range: 0.1 to 60 seconds
  • Alarm output: NE43, Software or Hardware selectable. Upscale (21 mA) or Downscale (3.6 mA) Surge Suppression Integral surge suppression available with option code S1
  • Ambient temperature: -40 to 85ºC (-40 to 185ºF) Ambient
  • Humidity: 0 to 100% RH
  • Linearization: 21 Point Table Available
  • Enclosure: Dual Compartment
  • Enclosure material: Cast Low Copper Aluminum with Powder Coat or 316 Stainless Steel
  • Device tag material: AISI 316 Stainless Steel
  • Electrical connection: Two M20 x 1.5 or two 1/2in. FNPT, adapters and bus connectors also available
  • Ingress protection: IP66, NEMA 4X

Magnetostrictive Level Transmitter LMT200 Sensor Tube

  • Material:
    Standard: 316/L Stainless Steel
    Options: Alloy 20, Hastelloy® C-276, FEP-TEFLON® jacketed, electropolished 316/316L Stainless Steel, others on request
  • Standard probe length: 304.8mm to 15.24 m (1 to 50 ft); 90-degree probes (SEH Option) 304.8mm to 7.62m (1 to 25 ft)
  • Probe length tolerance:
    Standard/Options: ± 3.2mm (0.125in) up to 3.0m (10ft); +/- 6.4mm (0.25in) up to 6.0m (20ft);
    ± 9.0mm (0.35in) up to 9.0m (29.5ft); +/- 25.4mm (1.0in) up to 15.24m (50ft)
  • Mounting:
    Stainless Steel Clamps for KM26 Magnetic Level Gauge Chamber Included; Optional Vibration Isolation Mounts

HMI indicator (pilihan)

• Tampilan bentuk gelombang untuk performa perangkat
konfirmasi
• Tampilan level saat ini serta antarmuka atau suhu media pengukur (opsional)
• Aplikasi–visualisasi khusus yang dapat dilakukan pengguna
Pilih. Empat halaman operator dapat dikonfigurasi untuk ditampilkan
beberapa nilai secara paralel
• Diagnostik kesalahan teks biasa sesuai dengan NE107
• Pengaturan parameter yang dipandu menu dengan empat tombol
• Fungsi 'Pengaturan mudah' untuk commissioning cepat
• Pengaturan parameter perangkat melalui kaca depan
dengan perumahan ditutup
• Selama operasi berlangsung, indikator HMI dapat
terhubung atau terputus dan oleh karena itu juga digunakan sebagai a
alat konfigurasi untuk perangkat lain
Editor