Informasi Hengesbach PZM 100/101 Flush-Mounted Pressure and Level Transmitter
Hengesbach PZM 100/101 Flush-Mounted Pressure and Level Transmitter cocok untuk melakukan pengukuran tekanan dan tingkat pengisian di saluran pipa dan wadah. Sistem koneksi proses modular menawarkan berbagai adaptor koneksi dan membantu memangkas biaya dalam jangka panjang.
Sambungan proses yang dipasang rata dengan seal O-ring dan membran baja tahan karat disertifikasi untuk EHEDG tipe EL-ASEPTIC CLASS 1 dan dengan demikian ditentukan sebelumnya untuk pengukuran yang memenuhi persyaratan kebersihan yang paling ketat sekalipun.
Rentang pengukuran sensor dari sel pengukur tahan vakum piezoresistif dengan membran baja tahan karat dari pemancar tekanan Hengesbach PZM berkisar dari -1/0…0,35bar hingga -1/0…100bar.
Rentang pengukuran khusus dimungkinkan untuk kedua versi. Semua pemancar tekanan dalam seri 100/101 dirancang untuk aplikasi universal dan, khususnya, untuk aplikasi dengan suhu tinggi terus-menerus hingga 200°C. Selain itu, dengan menggunakan tampilan di tempat dengan seri 100 dan modul tampilan dan pengoperasian OPUS M dalam seri 101, pemancar tekanan dapat dengan mudah dibaca, dikonfigurasi, dan didiagnosis.
Fitur Hengesbach PZM
- Sistem koneksi proses modular bersertifikasi EHEDG-aseptik
- pengukuran presisi ≤ ± 0,15% FS
- Matikan 10
- layar terintegrasi atau eksternal dan modul operasi OPUSM
- bukti vakum dan sangat aman
- entri langsung dari parameter dengan tampilan teks biasa
- mudah dibersihkan dan kelas perlindungan tinggi IP 67 dan IP69K
- kekuatan aplikasi: pengukuran tekanan konten dan proses / pengukuran vakum bahkan pada suhu tinggi
Spesifikasi Hengesbach PZM
| General details | |||||||||
| Device type / measuring principle | PZM 100/101: piezoresistive | ||||||||
| VRM 100/101: capacitive | |||||||||
| Input | |||||||||
| Measuring ranges | PZM 100/101 | VRM 100/101 | |||||||
| Standard nominal measuring range [bar] | relative | OP | absolute | OP | relative | OP | absolute | OP | |
| OP = overload protection [bar] | 0…0.35 | 1 | 0…4 | 25 | |||||
| 0…1 | 3 | 0…1 | 3 | -1/0…4 | 25 | 0…10 | 40 | ||
| -1/0…2.5 | 8 | 0…2.5 | 8 | -1/0…10 | 40 | 0…20 | 40 | ||
| Special measuring ranges are available on request. | -1/0…5 | 15 | 0…5 | 15 | -1/0…20 | 40 | 0…40 | 60 | |
| -1/0…10 | 30 | 0…10 | 30 | -1/0…40 | 60 | 0…70 | 105 | ||
| -1/0…30 | 90 | 0…30 | 90 | -1/0…70 | 105 | ||||
| -1/0…100 | 250 | 0…100 | 250 | ||||||
| Setting the measuring ranges | Via the keypad of the OPUSM display and operating module / via the integrated on-site display | ||||||||
| Setting ranges | Start the measuring zero: | 0…90% of the sensor’s nominal measuring span | TD=10 | ||||||
| Measuring span: | 10…100% of the sensor’s nominal measuring span | ||||||||
| Burst pressure DIN16086 | ≥ 4-fold measuring range | ||||||||
| Output | |||||||||
| Output signal | 2-wire: 4…20mA with a test circuit connection in the device | ||||||||
| Fault signal | Optional: 3.8mA, 22mA, hold (i.e. holding the last value) | ||||||||
| Current limitation | 3.85mA and 21.5mA (normal operation) | ||||||||
| Integration time | Continuously selectable between 0 and 300s (setting time after a pressure leap) | ||||||||
| Measuring accuracy | |||||||||
| Reference conditions | acc. to DIN IEC 770 | ||||||||
| Linearity, hysteresis and repeatability as per the limit point method DIN IEC 770 | ≤ ± 0.15% of the sensor’s nominal measuring range | ||||||||
| DIN IEC 770 | |||||||||
| Activation time | < 5s (the device will carry out a self-test.) | ||||||||
| Setting time (without damping) | < 200ms | ||||||||
| Long-time drift | ≤ 0.2% of the span per year | ||||||||
| Thermal hysteresis | ≤ ± 0.75% beginning of the measuring range / ≤ ± 0.8% end of the measuring range (VRM) | ||||||||
| ≤ ± 0.2% of the sensor’s nominal measuring range / 10K (-20…+80°C) from 4 bar (PZM) | |||||||||
| ≤ ± 0.3% of the sensor’s nominal measuring range / 10K (-20…+80°C) up to 0.6 bar (PZM) | |||||||||
| Conditions of use | |||||||||
| Installation position / calibration position | Any position / standing vertically | ||||||||
| Medium temperature | PZM: | T1: | -40…+125°C (140°C over one hour at the most) | ||||||
| T2: | -40…+200°C (high-temperature version) | ||||||||
| VRM: | -40…+140°C | ||||||||
| Ambient storage temperature | Type 101: | -40…+85°C | |||||||
| Type 100: | -30…+75°C | ||||||||
| (Below -20°C cable breakage might occur and the display’s function may be impaired.) | |||||||||
| Protection class acc. to EN60529 | IP 67 and IP 69K | ||||||||
| Electromagnetic compatibility | Sensitivity against interference: acc. to DIN IEC 61000-6-2 | ||||||||
| Interference radiation: | acc. to DIN IEC 61000-6-4 | ||||||||
| Construction | |||||||||
| Electrical connection | – Standard: cable screw connection M16x1.5, nickel-plated brass, stainless steel available on request | ||||||||
| – Optional: round plug-in connector M12x1, nickel-plated brass, stainless steel available on request | |||||||||
| – Optional: angle plug acc. to EN 175301-803 | |||||||||
| – Optional: reference cable | |||||||||
| Process connection | – Membrane, flush-welded on the front, CrNiSt, other materials available on request | ||||||||
| – EHEDG type EL-ASEPTIC CLASS 1, certified connection system PZM / VRM | |||||||||
| with press screw M38x1.5 and elastomer sealing | |||||||||
| – Process seal EPM (FDA) (temperature range: -20…+150°C) | |||||||||
| – Process seal FPM (FDA) (temperature range: -40…+200°C) | |||||||||
| Materials | – Field housing / lid: | CrNiSt 1.4301 (304) | |||||||
| – Housing seal: | FPM (Viton®) | ||||||||
| – Pressure compensation element: | polyamide | ||||||||
| – Inspection gauge (type 100): | polycarbonate | ||||||||
| – Process connection/connection adapter: | CrNiSt 1.4404 (316L) | ||||||||
| – Process membrane: | CrNiSt 1.4435/1.4404 (316L) | ||||||||
| – Locking screw (type 101): | CrNiSt 1.4301 (304) | ||||||||
| – Reference cable: 5-wire with reference tube: PUR (recommended: 80m maximum) | |||||||||
| Filling fluid | PZM: | silicon oil (FDA) | |||||||
| VRM: | medical mineral oil (FDA) | ||||||||
| Display and operation | |||||||||
| Display | LCD, 4-digit numerical display, and 5-digit alphanumerical display | ||||||||
| Type 100: | integrated on-site display (cannot be separated from the device) | ||||||||
| Type 101: | external OPUSM display and operating module | ||||||||
| Displayable units | Pressure: | mbar, bar, psi, Pa, mH2O, mmHg, Torr, atm, at, kg/cm² | |||||||
| Temperature*1: | °C, °F, K, °R, °Ré | ||||||||
| Additional displays | Output current in mA or % (in relation to the span) | ||||||||
| Operation | 100.00.00 | via the configuration menu with the integrated on-site display | |||||||
| 101.00.00 | via the configuration menu with the external OPUSM display and operating module | ||||||||
| Auxiliary energy resources | |||||||||
| Power supply/burden | 12-36V DC, max. burden: (V supply – 12V) / 24mA | ||||||||
| Accessories 100 series | |||||||||
| OPUSM display and operating module | External display and operating module, CrNiSt, IP 67, 41x70mm, 1m connection cable and round plug-in connector M12x1 | ||||||||
| Certificates | Calibration certificate | ||||||||
| Declaration of conformity | |||||||||
| Material inspection certificates as per EN 10204 | |||||||||
| EHEDG certificate | |||||||||
Download Data Sheet: Hengesbach PZM 100-101 Flush-Mounted Pressure and Level Transmitter
Sumber : Hengesbach.com | inaparts.com
Baca Juga :
